Standing water at the bottom of your dishwasher after a cycle is annoying, but it rarely means the machine is finished. In most cases the water cannot get out because something simple is blocking its path: a clogged filter, a kinked drain hose, or food stuck in the drain pump. Work through these fixes in order, from the easiest to the ones that need a little more effort, and check after each step by running a short rinse cycle.
Before you start, switch the dishwasher off at the wall or the breaker, and keep a few old towels and a shallow bowl nearby. A little water will spill when you open the filter or disconnect a hose, and that is normal.
1. Clean the filter
The filter sits at the bottom of the dishwasher tub, usually under the lower spray arm. Twist it anti-clockwise to lift it out, then rinse it under a running tap and scrub it with an old toothbrush. Food, grease and bits of paper collect here faster than most people expect, and a blocked filter alone can stop the machine draining.
While the filter is out, scoop out any standing water and food debris from the sump underneath it. Put the filter back and make sure it clicks or twists firmly into place. A loose filter lets food straight into the pump, which causes the next problem on this list.
2. Check the drain hose
The drain hose runs from the back of the dishwasher to the sink drain or the garbage disposal. Pull the dishwasher out just enough to see the hose, or look under the sink, and check for kinks, sharp bends or a hose squashed flat against the wall. Straighten any kink and make sure the hose loops up high under the sink before it drops down to the drain. That high loop stops dirty sink water flowing back into the dishwasher.
If the hose looks fine from the outside, disconnect it at the sink end with the bowl underneath and check for a clog. Food and grease can build up inside it, especially near the connection. Flush it through with hot water and refit it tightly.
3. Clear the garbage disposal connection
If your dishwasher drains through a garbage disposal, the connection can be the problem. First, run the disposal for a few seconds with cold water running. A full disposal blocks the dishwasher drain completely, and this one step fixes the problem surprisingly often.
If the disposal was recently installed or replaced, the dishwasher inlet plug may still be in place. New disposals ship with a small plastic knockout plug blocking the dishwasher inlet, and the installer is supposed to knock it out. If it was never removed, the dishwasher has never been able to drain properly. This needs the disposal disconnected to fix, so if you are not comfortable with that, call a technician.
4. Clean the air gap
Many kitchens have a small chrome cylinder on the sink, next to the tap. That is the air gap, and it stops dirty water flowing back into the dishwasher. Lift off its cap and check inside for food and grease. A blocked air gap can push water back into the tub or all over the worktop.
Clean it out, replace the cap, and run a short cycle. If water sprays out of the air gap while the dishwasher runs, the blockage is further down the drain hose or the sink drain itself.
5. Check the drain pump
The drain pump sits at the bottom of the machine and pushes water out. Small items like glass shards, olive stones, bones and bits of broken crockery can jam it. With the power off and the filter removed, reach carefully into the sump area and feel for anything hard or sharp. Wear a glove, because broken glass hides in there more often than people think.
If you find debris, remove it and run a rinse cycle. If the pump hums but does not move water, or makes a loud grinding noise, the pump motor may have failed. That is a replacement part, not a cleaning job.
6. Look at the sink drain itself
Sometimes the dishwasher is fine and the sink drain is the problem. If the kitchen sink also drains slowly or gurgles, the shared drain pipe is partly blocked. Run hot water down the sink, clear the sink trap if you know how, and see if the dishwasher drains normally afterwards.
Do not pour chemical drain cleaner into the dishwasher. It can damage the seals and the pump, and it leaves residue on the dishes. Hot water and mechanical cleaning are safer for this machine.
7. Check the door latch and the cycle
A dishwasher that does not latch properly may stop mid-cycle, before the drain stage, and leave water sitting in the tub. Close the door firmly until you hear the latch click, and check that nothing is sticking out of the racks and stopping the door closing fully. Then try a drain or cancel cycle. Most machines drain when you press cancel and hold it for a few seconds.
If the machine runs a full cycle, fills and washes, but never drains, the control board or the drain solenoid may be at fault. That is the point to stop and call a professional.
When to call a professional
Call a technician if the pump hums or grinds after cleaning, the machine drains only sometimes, water backs up into the sink, or you find the disposal knockout plug still in place and do not want to open the disposal yourself. Also call one if the dishwasher is over ten years old and the repair quote is close to half the price of a new machine. As with most appliance repairs, that 50 percent rule is a useful guide: if fixing it costs half of replacing it, replacement usually wins.
Most of the time, though, the fix is a dirty filter or a blocked hose. Clean the filter first, check the hose, and run the disposal. Those three steps alone clear the problem in most homes, with no parts and no call-out fee.
Related guides and trusted sources
- Read next on Snaptrroid: Refrigerator Not Cooling? 8 Causes and Fixes to Try First
- Read next on Snaptrroid: Samsung Washing Machine Error Codes: What Each Code Means and How to Fix It
- Trusted source: U.S. Department of Energy — Energy Saver: Dishwashers
- Trusted source: ENERGY STAR — Dishwashers






