A Samsung refrigerator does not show an error code to annoy you — it is telling you exactly which part it cannot hear from. The code is usually two digits and a letter, like 22E or 39E, and each one points at a sensor, a fan or the ice maker. Learn the handful of common ones below and you can tell in two minutes whether the fix is a free thaw, a reset, or a job for a technician. One warning first: code meanings can vary slightly by model, so always match the code to your exact model in the manual — and never unplug the fridge or press the panel to clear a code unless the steps for that code say so, because that can make diagnosis harder.

Start with the simplest check of all: write the code down before you touch anything. Codes can disappear after a power cycle, and a technician who knows the code can diagnose the fault in minutes instead of guessing. Then work through the code you have below.

1. OF OF — Cooling Off (demo) mode, not a fault

If the display reads OF OF (sometimes shown as O FF) and nothing is cooling, your fridge is almost certainly in Cooling Off mode — the showroom setting shops use so the lights work but the compressor never runs. This is a setting, not a breakdown, and it is the most common “fault” on a new or newly moved Samsung. To turn it off, press and hold the top two buttons on the left side of the display together for about 5 to 8 seconds until you hear a chime. The display should return to showing temperatures, and cooling should start within a few hours. If it comes back on its own, a control board issue is possible — but try the button hold first.

2. 21E and 22E / 22C — fan errors, the most common codes

Samsung lists 21E as a freezer fan error and 22E or 22C as a fridge fan error: the electronics are not sensing the fan turning when it should be. The usual cause is ice: a door left open too long, or a gasket that does not seal, lets moist air in, and the moisture freezes around the fan until it cannot spin. Samsung’s own step for 22E is to unplug the refrigerator, leave the doors open for a few hours so it fully defrosts, then plug it back in and close the doors. Keep food in a cooler while you do this. If the code clears and stays away, the cause was ice — check the door gaskets seal fully and do not overpack the freezer, which blocks airflow. If the code returns after a full thaw, the fan motor itself is likely failing and needs replacing. Samsung’s own support page lists these codes and their meanings at samsung.com.

3. 39E / 39C and 40E / 40C — ice maker and ice room fan

39E or 39C is an ice maker function error: the ice maker cannot complete its normal cycle. First check for the simple causes — an ice jam in the tray, a kinked or frozen fill tube, or the ice maker switched off. Clear any visible ice, turn the ice maker off for a few minutes and back on, and see if it cycles. 40E or 40C is the ice room fan error: the fan in the ice compartment is not running, often because ice has built up around it. Clear any ice you can see and let the compartment thaw; if either code keeps returning after that, the part behind it — the ice maker assembly or the fan motor — usually needs a technician, because both sit behind panels that are easy to damage.

4. 5E, 8E, 14E and 33E — sensors and the defrost system

5E is a refrigerator defrost sensor error: the sensor that tells the fridge when to melt frost off the evaporator is giving a reading the board cannot trust. 8E and 14E are ice maker sensor errors, and 33E is the ice pipe heater. These are sensor and heater faults, and unlike a fan iced up by an open door, they rarely have a DIY fix beyond checking the obvious — that the fridge has power, that no wire is visibly pinched in the door hinge, and that a recent power cut is not the real story. If a sensor code appears right after a power outage, a full power cycle (unplug for a minute, plug back in) sometimes clears it; if it returns, the sensor itself has usually failed and needs testing with a multimeter and replacing. Do not keep resetting a sensor code and hoping — a failed defrost sensor lets frost build until the fridge stops cooling properly.

5. 88 88 and PC ER — communication faults

88 88 usually appears at startup after a power interruption, and Samsung lists it as a communication fault between boards. Try switching the breaker off for a full 60 seconds and back on; if the display returns to normal temperatures, it was a one-off glitch. PC ER (sometimes shown as PC CH) is a similar communication fault between components, often after a power surge. If either code survives a breaker reset, the main control board is the likely suspect — that is a technician job, not a DIY one, and it is worth getting a quote before agreeing, since board replacement is one of the more expensive fridge repairs.

6. Older models: the blinking dash

If your Samsung is an older side-by-side or French door model, it may not spell out a code at all — instead one segment of the temperature display blinks. Each of the 13 segments stands for a different fault: segments 1–7 on the fridge display and 8–13 on the freezer display. The most common ones map to the same faults as the letter codes above — ice maker sensor, fridge fan, freezer fan and defrost sensor. Count which segment is blinking, note whether it is on the fridge or freezer side, and look it up against your model’s tech sheet (usually tucked behind the kick plate or inside the control panel cover). The same fixes apply: thaw first, then suspect the part.

When to stop and call a technician

Call for service when a code returns after you have done the full thaw or reset for it, when the code is a sensor or communication fault (5E, 8E, 14E, 33E, 88 88, PC ER), or when the fridge is not cooling at all and no code is showing — that last one can be a compressor or sealed-system problem. Before the visit, write down the code, the model number (inside the fridge on the wall), and what you already tried; it saves the technician’s first half hour. And if the fridge is simply not cooling with no code at all, our refrigerator not cooling guide walks through the coils, vents and door seals to check first — and for a similar decoder on the laundry side, our Samsung washing machine error codes guide covers the washer’s codes the same way.

Quick reference table

  • OF OF: Cooling Off (demo) mode — hold the top two left buttons 5–8 seconds until the chime
  • 21E: Freezer fan error — thaw fully; if it returns, fan motor
  • 22E / 22C: Fridge fan error — unplug, doors open a few hours, plug back in; check gaskets
  • 39E / 39C: Ice maker function error — clear jams, reset the ice maker
  • 40E / 40C: Ice room fan error — clear ice, thaw; if it returns, fan motor
  • 5E: Fridge defrost sensor error — power cycle once; if it returns, call service
  • 8E / 14E: Ice maker sensor error — call service
  • 33E: Ice pipe heater — call service
  • 88 88 / PC ER: Communication fault — breaker off 60 seconds; if it returns, call service

A code is good news, in its own way: the fridge is telling you where to look. Read it, write it down, thaw or reset once — and let a technician take it from there if the code comes back.

Related guides

Similar Posts