An LG washing machine almost always warns you before it gives up completely. The warning is the two-letter code flashing on the display — OE, IE, UE and their cousins. The trouble is that the code alone tells you nothing unless you know the language.
This guide translates the most common LG washing machine error codes into plain English: what each one means, the safe fix you can try yourself in a few minutes, and the point where you should stop and call a technician instead.
Safety first: before you open any panel, clean any filter or tilt the machine, switch it off and unplug it, and turn off the water taps. If you smell burning, see scorch marks, or water is leaking near electrical parts, do not run the machine again — call a technician.
LG washing machine error codes — quick table
| Code | Meaning | First fix to try |
|---|---|---|
| OE | Drain error — water is not draining | Clean the drain pump filter |
| IE | Inlet error — water is not filling | Check taps and inlet filters |
| UE / uE | Unbalanced load | Redistribute the clothes, level the machine |
| LE | Motor locked error | Unplug for 10 minutes, reduce the load |
| DE / dE | Door error | Close the door firmly, check the latch |
| TE / tE | Heating sensor error | Usually a technician job |
| CL | Child lock is on (not an error) | Hold the lock buttons for 3 seconds |
| PE | Water level sensor error | Restart the machine; sensor may need replacing |
| AE | Leak detected / auto shut-off | Find and fix the leak, dry the base |
| FE | Overfilling error | Turn off the taps; inlet valve may be stuck |
OE — drain error
What it means: the machine tried to empty the water and could not. This is the single most common LG error, and it is usually something simple blocking the drain.
Fix it yourself:
- Unplug the machine. Open the small flap at the bottom front corner.
- Place a shallow tray and towel underneath, then slowly unscrew the drain pump filter. Water will come out — go slowly.
- Clean the filter. Coins, hairpins, lint and small socks are the usual culprits.
- Check the drain hose at the back: it should not be kinked, squashed, or pushed too far down the standpipe.
- Screw the filter back in firmly, run a short rinse or spin cycle, and watch for the code.
Call a technician if: the filter and hose are clear but OE returns — the drain pump itself may have failed.
IE — water inlet error
What it means: the drum is not filling with water, or it is filling far too slowly.
Fix it yourself:
- Make sure both water taps behind the machine are fully open.
- Straighten any kinks in the inlet hoses.
- Turn the taps off, unscrew the inlet hoses where they meet the machine, and rinse the small mesh filters inside the inlet valves — they clog with grit and limescale over time.
- In winter, check that the hoses are not frozen.
Call a technician if: water pressure in the home is fine and the filters are clean, but IE keeps appearing — the inlet valve or its wiring may be faulty.
UE / uE — unbalanced load
What it means: the load inside the drum is uneven, so the machine refuses to spin at full speed to protect itself. A small uE means the machine is trying to rebalance on its own; a capital UE means it gave up and needs your help.
Fix it yourself:
- Pause the wash and open the door once the drum stops.
- Untangle the load and spread items evenly around the drum. A single heavy item — a bath mat, a blanket, one pair of jeans — causes most UE errors.
- Avoid washing one heavy item alone; add a couple of towels to balance it.
- Check that the machine sits level on the floor. If it rocks when you push a corner, adjust the feet until it is solid.
Call a technician if: the machine is level, loads are balanced, and UE appears on almost every wash — worn shock absorbers or suspension rods are likely.
LE — motor locked error
What it means: the motor tried to turn the drum and could not — the control board cuts power to protect the motor.
Fix it yourself:
- Unplug the machine and leave it unplugged for 10 minutes. This resets the motor’s thermal protection, which trips when the machine is overloaded.
- Take out part of the load if the drum was packed tight, and remove anything jammed between the drum and the door seal.
- Plug back in and run a short cycle with a smaller load.
Call a technician if: LE appears with a light or empty load, or you hear grinding when the drum turns — the motor, its sensor, or the wiring harness needs inspection. On new machines, LE can also show up if the shipping bolts were never removed.
DE / dE — door error
What it means: the machine thinks the door is open, or the lock cannot engage.
Fix it yourself:
- Open the door and close it again firmly until you hear the click.
- Check the door seal for a trapped sock or a build-up of detergent residue stopping the door from seating.
- Inspect the latch on the door and the lock on the frame for visible damage or looseness.
Call a technician if: the door closes properly but DE stays — the door lock assembly is a common wear part and usually needs replacing.
TE / tE — heating sensor error
What it means: the thermistor — the sensor that measures water temperature — is giving readings the control board cannot trust, or the heating circuit has a fault.
Fix it yourself: honestly, there is very little. Unplug the machine for 10 minutes and try once more; a one-off glitch can clear.
Call a technician if: TE returns, which it usually does. The thermistor or heater needs testing with a meter and replacing if faulty.
CL — child lock (not an error)
What it means: CL is not a fault at all. Child lock is switched on, so the buttons are disabled — usually because someone leaned on the panel.
Fix it yourself: press and hold the two buttons marked with the child lock symbol (on most models, Temp and Option, or the button labelled with a small lock icon) for about 3 seconds until CL disappears. The exact pair is printed on your control panel and in the manual.
PE — water level sensor error
What it means: the pressure switch that tells the machine how much water is in the drum is not reporting correctly.
Fix it yourself: unplug the machine for 10 minutes and restart. If PE returns, the sensor’s thin air tube may be blocked or split — some confident owners check it, but it sits inside the cabinet.
Call a technician if: PE comes straight back after a reset. The sensor usually needs replacing.
AE — leak detected / auto shut-off
What it means: on models with a leak sensor in the base, water where it should not be has triggered an automatic shut-off.
Fix it yourself:
- Unplug the machine and turn off the taps.
- Find the water: check the inlet hoses, the drain hose, the door seal and the detergent drawer for leaks.
- Fix the source, mop up, and let the base dry fully — the sensor will keep the machine off while it is still wet.
Call a technician if: there is no visible leak anywhere but AE appears, or the machine leaks again immediately.
FE — overfilling error
What it means: the water level rose higher than it should, or the machine keeps filling when it should have stopped.
Fix it yourself: turn off the water taps first — do not let the machine keep filling. Unplug it, and let the machine drain on a drain-only cycle if it will run. A stuck inlet valve is the usual cause.
Call a technician if: the machine fills even when it is switched off (taps off stops it) — the inlet valve is stuck open and needs replacing.
How to reset an LG washing machine
Many one-off codes clear with a simple reset:
- Unplug the machine (or switch off the socket) for 10 minutes.
- Press and hold the power button for 5 seconds while it is unplugged to drain residual charge.
- Plug it back in and run a short empty cycle.
If the same code returns on the empty cycle, it is a real fault, not a glitch — work through the section for that code above.
Stop errors before they start
- Clean the drain pump filter once a month — it prevents most OE errors.
- Leave the door and detergent drawer slightly open after washes to stop mould and seal damage.
- Do not overload: the drum should be at most three-quarters full for a normal load.
- Use the right amount of detergent. Too much creates excess suds, unbalanced spins and residue in the drain.
- Check pockets before washing. Coins and pins are the top cause of blocked pumps and torn seals.
Related guides and trusted sources
- Read next on Snaptrroid: Samsung Washing Machine Error Codes
- Read next on Snaptrroid: Refrigerator Not Cooling? 8 Causes and Fixes
- Trusted source: LG support
The bottom line
Most LG washing machine error codes are the machine protecting itself from a small, fixable problem: a clogged filter (OE), a blocked inlet (IE), an uneven load (UE), or a door that is not quite shut (DE). Work through the simple checks first — they cost nothing and solve the majority of cases. Save the technician call for the sensor, motor and heating codes (LE, TE, PE) and for anything involving leaks near electrics.



